Estimate Concrete Prices Across Texas
Use this Concrete Cost in Texas calculator to estimate 2026 budgets for slabs, patios, driveways, foundations and ready-mix orders. Calculate cubic yards from dimensions, add waste, enter a local Texas ready-mix price, compare installed project ranges and check contractor bids by cost per square foot. All figures are planning estimates—actual Texas concrete prices vary by city, supplier, delivery distance, mix design, reinforcement, site access, soil preparation, finish, labor and permit requirements.
Estimate installed slab cost, model a ready-mix order, calculate concrete volume and material cost from dimensions, or compare contractor bids by effective price per square foot.
Estimate area, cubic yards and a broad installed-cost range for common Texas concrete projects.
Planning estimate only. Texas bids can vary with excavation, subgrade, reinforcement, forms, pumping, access, finish, demolition, permits and local labor.
Enter the cubic yards you plan to order and the current price quoted by your local Texas supplier.
Replace $180 with your actual local quote.
Fuel, waiting time, short-load, pumping, special mix, fiber, color and weekend charges may be separate depending on supplier.
Calculate cubic yards from dimensions, add waste and multiply by your Texas ready-mix price.
Compare up to three total bids by effective cost per square foot.
Compare scope as well as price: excavation, base, rebar, slab thickness, finish, pump, demolition, drainage and permit responsibility may differ.
Concrete cost in Texas varies substantially because Texas contains several large construction markets and enormous distances between regions. Dallas–Fort Worth, Houston, Austin and San Antonio each have dense ready-mix networks, while smaller cities and rural projects may face different delivery economics. Soil conditions, heat, site access, reinforcement, pumping and local labor also influence installed cost.
For a statewide starting point, Concrete Network's 2026 guide reports an average ready-mix price of about $179.95 per cubic yard and emphasizes that regional prices vary. Texas local-cost pages show how wide installed pricing can be: an April 2026 Austin guide from Angi places concrete slabs around $4–$10 per square foot, while a February 2026 Dallas Angi guide places concrete patios around $4–$12 per square foot. North Texas driveway guidance reports contractor quotes roughly $7–$21 per square foot, depending on finish and scope.
These figures should be used as planning ranges rather than a universal Texas rate. The most reliable budget replaces the calculator's default ready-mix value with a current quote and compares multiple contractor bids using the same scope, dimensions and finish.
| Project | 2026 Planning Range | Main Cost Drivers | Texas Context |
|---|---|---|---|
| Ready-mix concrete | Use local quote; ~$179.95/yd³ national average | Mix, distance, order size, additives | Major metro markets can be competitive; rural haul distance can matter. |
| Austin-area slab | $4–$10/ft² | Fortification, drainage, site conditions | Current Angi Austin 2026 range. |
| Plain concrete patio | $4–$12/ft² | Area, base, access, finish | Current Dallas Angi 2026 range. |
| Texas concrete driveway | $7–$21/ft² | Thickness, rebar, removal, finish | North Texas contractor range; premium decorative work higher. |
| Stamped concrete | $9–$22+ /ft² | Pattern, colors, borders, sealer | Current national decorative-concrete guidance. |
| Texas stamped patio | $15–$30/ft² | Design package, color, complexity | Published 2026 Texas patio guide range. |
| Colored or stained patio | $12–$25/ft² | Color system, prep, sealing | Published 2026 Texas patio guide range. |
| Exposed aggregate | $7–$18/ft² | Aggregate and finishing labor | Use local decorative-concrete bids. |
Project-specific ranges are more useful than one statewide installed price because a standard slab and a decorative driveway are fundamentally different scopes. Texas concrete bids should state dimensions, thickness, base preparation, reinforcement, finish and exclusions so the price can be compared fairly.
Ready-mix concrete is generally priced by the cubic yard, but the delivered invoice may include additional items. Small-load charges, delivery zones, fuel adjustments, waiting time, pumping, fibers, accelerators, retarders, integral color and special mix designs can change the effective price per yard.
Texas has an extensive ready-mix industry. Texas Materials describes itself as a major Central Texas ready-mix supplier, Lauren Concrete operates many locations across Central Texas, Cow Town Redi-Mix serves DFW and surrounding cities, and CEMEX has major Texas operations. The size of the supplier network does not create one statewide price; the relevant number is the quote from a plant that can serve your exact address and mix requirement.
Use your supplier's delivered price, not just a national average.
For a rectangular slab measured in feet, multiply length by width and by thickness converted from inches to feet. Then divide cubic feet by 27 to obtain cubic yards.
Example: 20 ft × 20 ft × 4 in ≈ 4.94 yd³ before waste.
A small allowance can cover minor subgrade variation, spillage and measurement uncertainty. The calculator includes 0%, 5%, 10% and 15% options so you can match the project instead of forcing a single waste factor.
The table below uses a 4-inch slab, 10% volume allowance and a sample ready-mix price of $180 per cubic yard. These are material-only examples before delivery fees, labor, base, reinforcement, forms, finishing, pumping or permits.
| Slab Size | Area | Base yd³ | yd³ + 10% | Concrete at $180/yd³ |
|---|---|---|---|---|
| 10 × 10 ft | 100 ft² | 1.23 | 1.36 | About $244 |
| 12 × 12 ft | 144 ft² | 1.78 | 1.96 | About $352 |
| 12 × 20 ft | 240 ft² | 2.96 | 3.26 | About $587 |
| 16 × 20 ft | 320 ft² | 3.95 | 4.35 | About $782 |
| 20 × 20 ft | 400 ft² | 4.94 | 5.43 | About $978 |
| 20 × 24 ft | 480 ft² | 5.93 | 6.52 | About $1,174 |
| 24 × 24 ft | 576 ft² | 7.11 | 7.82 | About $1,408 |
| 24 × 30 ft | 720 ft² | 8.89 | 9.78 | About $1,760 |
| 30 × 30 ft | 900 ft² | 11.11 | 12.22 | About $2,200 |
| 30 × 40 ft | 1,200 ft² | 14.81 | 16.30 | About $2,933 |
Expansive or unstable soils can increase excavation, base and structural requirements.
Hot-weather placement can affect scheduling, crew size, finishing and mix-management decisions.
Driveways, foundations and structural slabs may require more concrete and steel than basic patios.
Texas is large; plant location and haul distance can materially affect delivered ready-mix cost.
Stamped, stained, exposed aggregate and polished finishes add labor and materials.
Ready-mix is only one part of installed cost. Site work, reinforcement, placement, finishing and local logistics can all change the final number.
DFW is one of the largest concrete markets in Texas. A May 2026 Dallas slab-cost guide reported ready-mix pricing around $119–$141 per cubic yard in that market and noted short-load surcharges on orders under eight yards. A North Texas driveway guide reports contractor quotes ranging roughly from $7 to $21 per square foot, with standard poured concrete around $7–$10 per square foot and decorative tiers higher.
These local figures are useful context, but supplier prices and contractor quotes can change. For DFW projects, ask about minimum-load rules, rebar spacing, base preparation, demolition, pump requirements and whether the quoted price includes cleanup and sealing.
Angi's April 2026 Austin guide places concrete slab installation around $4–$10 per square foot on average. Austin projects may also involve drainage, impervious-cover rules and site-specific structural requirements. For ready-mix supply, Texas Materials describes itself as a major Central Texas supplier, while Lauren Concrete operates numerous plants throughout Austin and surrounding Central Texas communities.
Because the Austin metro stretches into fast-growing suburban and exurban areas, plant proximity can affect delivery. Provide the job address when requesting a quote rather than relying on a price from another side of the metro.
Houston has a deep ready-mix and building-material supply market, including major producers such as CEMEX. Concrete project pricing can still vary with travel, pump access, demolition, drainage and soil preparation. Residential slabs and driveways should be compared by full scope rather than only by concrete square footage.
Southeast Texas heat and rainfall also make scheduling, drainage and curing practices important project considerations. A contractor's approach to site preparation and water management can materially affect total cost and durability.
Compare site preparation, limestone excavation risk, delivery distance and reinforcement details.
Regional material supply and long-distance logistics can differ from Dallas, Houston and Central Texas.
Coastal exposure, drainage and project location can influence material and finishing decisions.
Local supplier coverage and jobsite distance matter; use delivered-price quotes tied to the project address.
Wind, heat, distance and market size can affect placement logistics and supplier pricing.
Rural access, soil, drainage and haul distance may matter more than statewide average pricing.
Concrete driveways typically need more structural capacity than patios. North Texas contractor guidance currently shows a broad range around $7–$21 per square foot, with basic poured concrete near the lower end and decorative finishes at the upper end. Removal of an existing driveway, thicker slabs, additional rebar, driveway aprons and drainage work can increase cost.
For a 600-square-foot driveway, a $7–$21 range corresponds to roughly $4,200–$12,600. That is a planning screen, not a Texas-wide guaranteed bid. The actual price should be based on thickness, reinforcement, base, finish and access.
Dallas homeowners are currently shown a $4–$12 per-square-foot concrete patio range by Angi. A separate 2026 Texas patio guide lists plain concrete around $8–$12 per square foot, stamped concrete around $15–$30, and colored or stained concrete around $12–$25. The difference between sources highlights why local scope and finish matter.
A basic broom-finish patio with simple access should not be compared directly with a multi-color stamped patio, even if both cover the same square footage.
Stamped concrete adds patterning, color and sealing to the base slab. Current 2026 national guidance commonly places stamped concrete around $9–$22 or more per square foot, while some Texas-specific patio guides show $15–$30 depending on finish package. Complex borders, multiple colors, hand detailing and premium sealers raise labor and material cost.
High temperatures can speed hydration and reduce working time, so contractors may adjust placement timing, crew size, mix design and curing procedures. Early-morning pours are common in hot conditions. These operational decisions can affect scheduling and cost even when the concrete quantity is unchanged.
Parts of Texas have expansive clay soils. Site-specific soil conditions can influence excavation, base preparation, slab design, reinforcement and foundation engineering. Do not reduce a structural foundation budget to a generic flatwork cost-per-square-foot number.
Poor drainage can undermine slabs, driveways and patios. Grading, swales, drains or extra base work may be part of a complete project scope and can materially change the price.
Foundation concrete should not be priced from a simple patio or flatwork number because structural work can include footings, grade beams, thickened edges, piers, post-tension systems, additional reinforcing steel and engineered slab details. In parts of Texas with expansive clay soils, foundation design may be driven by a geotechnical report or engineer's recommendations rather than a standard four-inch slab assumption. The concrete volume itself may represent only one part of the final foundation budget.
Garage slabs can also differ from basic patios. Vehicle loads, thickened edges, drainage slope, vapor barriers, reinforcement and connection details can increase both material and labor. If a garage slab is part of a new structure, use the structural drawings to calculate concrete for beams, footings or edge sections separately instead of multiplying the floor area by a generic cost per square foot.
For budgeting, separate the project into components: excavation and grading, base or select fill, reinforcing or post-tension work, concrete volume, pumping, finishing and any engineering or inspection requirements. That method makes contractor bids easier to compare and helps prevent a low flatwork rate from being applied to structural work.
Small sidewalks, pads, steps and walkways can have a high effective price per square foot because mobilization, forms, finishing and delivery costs are spread across a small area. A one- or two-yard ready-mix order may also be subject to minimum-load or short-load charges, while bagged concrete can require substantial labor for larger volumes. For this reason, the cheapest material option is not always the cheapest installed option.
When comparing a small-pour quote, ask whether it includes demolition, haul-off, forms, base preparation, reinforcement, concrete delivery, finish, control joints and cleanup. If the work is in or near a public right-of-way, the city may have separate standards or permit requirements for sidewalks, curb cuts or driveway approaches.
Combining several small areas into one pour can sometimes reduce mobilization or short-load costs, provided the crew can place and finish the total volume safely within the concrete's working time. Discuss scheduling with the contractor and supplier rather than assuming a larger combined pour is always practical.
Texas is large enough that statewide averages can hide meaningful regional differences. Major metro areas may offer more supplier competition and contractor availability, but traffic, access restrictions and higher labor demand can increase installed cost. Rural areas may have simpler jobsite access but longer ready-mix haul distances and fewer contractors bidding on specialized work. West Texas projects can face long distances between plants, while dense urban sites may require pumping or smaller placement equipment.
Material pricing also changes with project specifications. A standard residential mix, high-strength structural mix, fiber-reinforced mix, colored concrete and specialty low-shrink or rapid-setting products should not be expected to carry the same per-yard price. Hot-weather placement, nighttime work, weekend scheduling or large commercial pours may also involve different supplier terms.
The practical approach is to use the statewide page for geometry and budgeting, then collect quotes tied to the exact ZIP code, mix specification and pour date. Keep the cubic-yard requirement consistent across quotes so you can identify whether differences come from material rate, delivery fees or project scope.
Texas does not have one simple permit fee or municipal construction rule that applies identically everywhere. Cities adopt and amend building codes locally. For example, Fort Worth currently lists the 2021 International Building Code and related 2021 codes among its adopted standards, with local amendments. Other Texas cities may use different editions or adoption schedules.
Concrete work involving buildings, foundations, structural slabs, drive approaches, sidewalks, right-of-way or commercial accessibility can trigger different review requirements. Texas Department of Licensing and Regulation also administers the Texas Accessibility Standards for applicable projects. Check the city, county and applicable state program before starting work.
Texas has a large ready-mix market. Central Texas suppliers include Texas Materials and Lauren Concrete; Cow Town Redi-Mix serves DFW and surrounding cities; CEMEX maintains substantial Texas operations; and Martin Marietta supplies ready-mixed concrete through its facility network. The Texas Aggregates & Concrete Association is a statewide industry trade association for concrete and aggregate producers and suppliers.
Supplier presence does not mean every plant serves every address or sells every mix at the same price. Request a quote with the project ZIP code, estimated yards, PSI or mix specification, delivery date and expected unloading method.
Continue planning with Concrete Calculator, Concrete Bags to Cubic Yards, Cubic Feet to Cubic Yards, Cubic Yards to Cubic Feet, Concrete Cost in Oklahoma, Concrete Cost in Louisiana, Concrete Cost in New Mexico and Concrete Cost in Arkansas.
This page is a budgeting tool, not a supplier quote or contractor bid. Pricing changes by location and over time. The calculator intentionally keeps ready-mix prices and fees editable. Texas-specific installed ranges are presented with source context so they are not mistaken for one official statewide rate.
Quick answers about ready-mix prices, slabs, driveways, patios, stamped concrete and Texas project budgeting.