Estimate Concrete Prices Across Minnesota
Use this Concrete Cost in Minnesota calculator to estimate ready-mix, slab, bagged concrete and installed project costs. Enter your own local quote for the best budget, or start with editable 2026 planning values for Minnesota projects.
Estimate a slab, ready-mix order, bagged-concrete project or installed cost per square foot. Every price field is editable so your supplier or contractor quote can replace the planning defaults.
Estimate cubic yards, ready-mix material, labor/finishing and extras for a rectangular slab.
Replace with your Minnesota supplier quote.
Calculate a ready-mix order using your cubic-yard quantity, price per yard and supplier fees.
Estimate bags and DIY material cost from project dimensions. Bag yield is selectable and the price per bag is editable.
Build a simple all-in estimate from slab area and editable unit rates for installation, preparation, reinforcement and demolition.
Concrete prices in Minnesota are best treated as a range, not a statewide fixed rate. A batch plant in central Minnesota, a short-load delivery in Twin Cities metro, and a residential slab installed in a tight-access Saint Paul lot can all have different economics. National 2026 ready-mix cost guides commonly place delivered concrete around the low-$100s to mid-$100s per cubic yard, while Minnesota-oriented estimators often use a planning figure around $160 per cubic yard. Minneapolis-specific 2026 data places many new concrete slabs around $4 to $8 per square foot on average, while local Twin Cities patio guidance commonly shows basic broom-finish work around $8 to $12 per square foot depending on scope, access and finish.
For that reason, this calculator starts at $160 per cubic yard for ready-mix but keeps the rate fully editable. The safest estimate is always the one built from your actual quote, specified mix, order quantity and delivery address.
When people search for the cost of concrete per yard in Minnesota, they are usually asking about ready-mixed concrete delivered by truck. For 2026 budgeting, a practical planning band is roughly $125 to $175 per cubic yard for standard ready-mix before project-specific extras, and this page starts at an editable $160 per cubic yard. Treat that as a budgeting input rather than a guaranteed market price.
A Minnesota-focused 2026 estimator also uses about $160 per yard as a base planning figure. Minnesota supplier Cemstone explains that actual pricing depends on the concrete mix, specialty additives or finishes and order size, and directs customers to request a current estimate. Delivery distance, minimum-load policies, cold-weather requirements, pumping, waiting time and jobsite access can all change the delivered invoice.
Then add delivery, minimum-load or short-load charges, pumping, waiting-time fees, admixtures and other supplier-specific costs.
The table below uses a 4-inch slab, a 10% volume allowance and a $160-per-yard ready-mix planning rate. It shows material only for the concrete itself, not labor, forms, reinforcement, gravel base, excavation, pumping, permits or finishing. Use it as a quick quantity-and-material check before obtaining local quotes.
| Slab Size | Area | Base Volume | Order +10% | Concrete @ $160/yd³ |
|---|---|---|---|---|
| 10 × 10 ft × 4 in | 100 ft² | 1.23 yd³ | 1.36 yd³ | $217 |
| 10 × 20 ft × 4 in | 200 ft² | 2.47 yd³ | 2.72 yd³ | $435 |
| 12 × 20 ft × 4 in | 240 ft² | 2.96 yd³ | 3.26 yd³ | $522 |
| 20 × 20 ft × 4 in | 400 ft² | 4.94 yd³ | 5.43 yd³ | $869 |
| 20 × 30 ft × 4 in | 600 ft² | 7.41 yd³ | 8.15 yd³ | $1,304 |
| 24 × 24 ft × 4 in | 576 ft² | 7.11 yd³ | 7.82 yd³ | $1,251 |
| 20 × 40 ft × 4 in | 800 ft² | 9.88 yd³ | 10.86 yd³ | $1,738 |
| 30 × 40 ft × 4 in | 1,200 ft² | 14.81 yd³ | 16.30 yd³ | $2,607 |
The distance from the batch plant to Minneapolis, Saint Paul, Rochester, Duluth or a rural site can affect freight, scheduling and minimum-order economics.
Strength, air entrainment, fibers, accelerators, retarders and special mixes can move the price above a basic ready-mix rate.
Cold-weather placement, winter protection and shortened working windows can add materials, labor and scheduling costs.
Long wheelbarrow runs, pump trucks, limited truck access, steep grades and urban staging can raise placement costs.
Concrete is time-sensitive after batching. The National Ready Mixed Concrete Association notes that ASTM C94 includes time/revolution requirements for discharge, which is one reason travel time and jobsite readiness matter. A delayed crew or blocked access can become a cost issue even if the material price per yard is unchanged.
A basic slab price often combines several categories: subgrade preparation, compacted stone base, forms, reinforcement, concrete, placement, screeding, finishing, control joints, curing and cleanup. A simple patio on good access and prepared soil may sit near the lower end of a local range, while a structural garage slab, reinforced driveway, thickened-edge slab or hard-to-reach backyard can cost more.
A 2026 Minneapolis cost guide from Angi reports that homeowners commonly spend about $4 to $9 per square foot for a new slab, with an average band around $4 to $8 per square foot for standard work. It also notes that thicker or more complicated foundation slabs can run much higher. Local Twin Cities contractor guidance places basic broom-finish patios around $8 to $12 per square foot. For budgeting, use the installed-cost calculator above and separate the categories you know rather than assuming every quote includes the same scope.
Multiply by 1.05 to 1.10 when you want a 5% to 10% ordering allowance.
Usually the practical choice for slabs, driveways, footings and larger pours where several cubic yards are needed. It reduces hand mixing and can improve consistency, but truck access, minimum orders, short-load fees and placement timing matter.
Useful for post holes, small pads, steps, repairs and isolated work. The material is easy to buy in small quantities, but mixing dozens of bags becomes labor intensive very quickly.
Do not assume that a quote in one Minnesota market is automatically a fair benchmark for another. Ready-mix is produced locally, so plant location, delivery route, traffic, truck availability, crew rates and winter scheduling all matter. The safest comparison starts with the same cubic-yard quantity, mix specification, pour date and placement conditions.
Record length, width and thickness. Use separate sections when the slab has different depths.
Convert the dimensions to cubic yards using the calculator above.
Consider 5% to 10% for grade variation, spillage and measurement uncertainty.
Ask for concrete rate, delivery, short-load, additives, pumping and waiting charges separately.
Budget forms, base, reinforcement, labor, finish, curing, permits and removal as applicable.
The ready-mix invoice is just one line in many projects. Site preparation, gravel, forming, reinforcement, pump rental, labor, finishing and demolition can exceed the cost of the wet concrete itself.
A perfect 4-inch subgrade is unusual. Small grade changes across a large slab create real volume differences. Many estimators include a modest allowance so the crew does not run short during placement.
Small orders can be convenient but may carry special pricing. Small Minnesota orders may be affected by supplier minimums, short-load or delivery charges, so compare the total delivered invoice—not only the per-yard line.
National guides are useful for planning, but Minnesota site conditions and labor quotes are local. Use broad published ranges to set expectations, then replace them with actual Minnesota bids.
Concrete permit rules in Minnesota are local, not one-size-fits-all. For example, the City of Rosemount states that a building permit is required for patios and concrete slabs, while Coon Rapids says a permit is not needed for an ordinary uncovered concrete patio. Structural slabs, foundations, garages, additions, steps and work connected to a building can follow different rules. Always check the city or county building department for the property before scheduling the pour.
Minnesota Department of Labor and Industry rules also depend on the contractor's scope. DLI states that a person or company contracting directly with an owner of one- to four-unit residential property to provide work in more than one special skill must hold a residential building contractor or remodeler license. DLI also operates contractor registration and an online license/registration lookup. Before signing a contract, confirm which license or registration applies and verify the contractor's current status through Minnesota DLI residential contractor licensing.
Continue planning with our Concrete Calculator, Concrete Slab Calculator, Concrete Bags to Cubic Yards, Cubic Feet to Cubic Yards and Concrete Cost Calculator. You can also compare regional guides such as Concrete Cost in Colorado, Concrete Cost in Arizona and Concrete Cost in Arkansas.
Use published cost guides for planning, but confirm current local prices directly before ordering.
Pricing changes over time. The calculator is for preliminary budgeting and does not replace a written supplier or contractor quote.
The concrete itself is only one layer of the final installed cost. This visual separates quantity, ready-mix, site work and finishing so the budget is easier to understand.
Quick answers about ready-mix pricing, slabs, delivery, quantities and budgeting in Minnesota.